MaxxECU Race ECU Generation 2 – Gen 2
$ 96.61

MaxxECU Race ECU Generation 2 – Gen 2

-4%

Delivery time: 3-5 Werktage

Worldwide delivery

  • 14 days right of widthdrawal
  • Short delivery times (1-2 days within Germany, foreign countries differ)
Description It’s here! The Generation 2 MaxxECU! The first of the GEN 2 out of the gates, the MaxxECU RACE GEN2 The MaxxECU brand, has fast become my favourite ECU manufacturer. We install and tune these daily here at the ‘Tuningshed’. I’ve literally spent hours on the dyno, tuning them. We’ve installed countless setups too. We can offer advice on ECU selection, and even with setup and first start. Best of all, we can tune the vehicle for you too. MaxxECU Race GEN 2 Included within the kit: MaxxECU Race & Limited time only free PVE MaxxECU Race Alluminium Mount Bracket Selected features Volumetric efficiency fuel tuning Boost control (triple stage) Launch Control Anti-Lag with cooldown features Traction and power management features Shift Cut and sequential gearbox control Flex Fuel Nitrous with purge and multiple stage control Knock control VANOS / VVTi variable cam timing Auto Transmission (8HP, 4l60/65/80/85) OEM CAN Integrations DSG / DCT / 8HP CAN Gearbox Control Internal logging up to 1000hz Waterproof to IP68 Built in 550kpa / 80psi Map Sensor 16 Injector 12 Ignition 16 GP Outputs 8 Pulse inputs 24 Analogue inputs 8 – Built in EGT Dual Wideband (LSU4.2 / 4.9 / 5.2) Dual CAN-BUS Dual Knock Dual USB-C Wi-Fi & Bluetooth Alluminium Case Target engines of MaxxECU RACE All 1-12 cylinder engines (2/4-stroke) Up to 12 cylinders fully sequentially Up to 12 cylinders maximum in wasted spark MaxxECU RACE GEN 2 inputs 8 Pulse inputs (VR/HALL) 2 with selectable 5/12v supply 24 Analogue inputs (selectable pullups) 8 Built in Exhaust Gas Temperature Inputs (K-Type) Built in Dual Wideband (LSU 4.2, 4.9 & LSU5.2 support) Dual Knock Sensor Input MaxxECU RACE outputs 16 Injectors (Peak-Hold / Low Impedance) / GP Outputs 12 IGN / GP Outputs (Selectable 5v / 12v / GND) 8 GP Outputs (GND) 4 GP Outputs ( 12V) 4 GP Outputs (H-Bridge / E-Throttle) MaxxECU RACE technical Superseal 1.0 Connectors Built in 550kpa / 80Psi Map Sensor, user serviceable Built-In accelerometer up to 8G ARM dual core CPU 6-22v operating range 16GB internal logging capacity, 1000hz, all 1600 channels USB-C 280mbit/s (M-Tune PC Communication) USB-C 12mbit/s (Tablet / Charging) Wifi communication with MTune and MDash Dual CAN bus for expansion modules, OEM vehicle CAN OBD2, gearbox Resolution on ignition 0.1 degrees Resolution on injectors 0.001ms Performs fuel and igniton calculations 3,000 times per second 200hz sampling on all EGT inputs 2000hz sampling rate on analogue / digital inputs Weigth: 700g 240 x 138 x 35mm including protruding connectors Black powder-coated aluminium case All inputs / outputs safeguarded agains overvoltage / reverse polarity and short circuit When ‘Backorder’ is stated, the Webshop will allow you order the item, but please allow 2-weeks for delivery. When ‘In Stock’ is stated, normally you will recieve your product within 2 working days. Link to the MaxxECU Website for more information MaxxECU ECU Videos

Safety instructions for Erzgebirge folk art pyramids.
• The pyramids are powered by burning candles! Therefore, make sure to keep a safe distance from curtains, furniture, upholstery and other flammable objects.
• Also remember that the pyramid is not a toy for children. Operation with an open flame may only take place under the constant supervision of adults.
• We accept no liability for damage caused by improper use or failure to observe these instructions.

Instructions for operation:
• Please only use high-quality candles that guarantee even burning. (Candles)
• Drafts can significantly affect the pyramid’s operation and should therefore be avoided at all costs.

Instructions for location:
• A solid and, above all, horizontal location (floor, table, etc.) is a prerequisite for a pyramid to run smoothly.
• When setting up the pyramid, make sure that the axis of the pyramid is in a vertical position. It must also be correctly positioned in the bearing.
• The middle part of the pyramid must be able to move freely.

Storage instructions:
• To ensure that the pyramid remains functional for many years, we recommend that you store it in a dry place.
• In addition, the pyramid should not be exposed to any major temperature fluctuations during storage.

Environmental damage caused by incorrect disposal of batteries

Batteries must not be disposed of in household waste. You are legally obliged to return old batteries so that proper disposal can be ensured. You can hand in old batteries at a municipal collection point or at a local retailer. As a distributor of batteries, we are also obliged to take back old batteries, although our obligation to take back is limited to old batteries of the type that we have or have had in our range as new batteries. You can therefore either send old batteries of the aforementioned type back to us with sufficient postage or hand them in free of charge directly in our store at the address given in the imprint.

Batteries are marked with the symbol of a crossed-out garbage can. This symbol indicates that batteries must not be thrown in household waste. For batteries that contain more than 0.0005 percent mercury (HG) by weight, more than 0.002 percent cadmium (Cd) by weight or more than 0.004 percent lead (Pb) by weight, the chemical name of the pollutant used is located under the garbage can symbol.

Dispose of electrical devices in an environmentally friendly manner

Electrical devices must not be disposed of with household waste. According to the European directive on waste electrical and electronic equipment, used electrical devices must be collected separately and sent to special collection and return systems. Owners of old devices from private households can hand them in at the collection points of the public waste disposal authorities or at the return points set up by manufacturers or distributors in accordance with the ElektroG.

Make sure that no beard hairs protrude in front of or into the mouth hole, otherwise no suction can be created and the cone can suffocate.

  • Remove the upper body
  • Light the incense cone (15 mm) at the tip and place it on a metal plate
  • Put the upper body back on and enjoy the scent
  • Then empty the ash into a non-flammable container.

 

  • Not a toy for children!
  • Please only use under adult supervision!
  • Caution, smoldering incense cones and metal plates are very hot!